Alteon AD3 설정 메뉴얼

 

► Alteon AceDirector 3 (AD3) 장비 설정

1. 콘솔 터미널 연결 설정

1-1. 콘솔 연결 및 하이퍼터미널 실행(시작 -> 프로그램 -> 보조프로그램 -> 통신 -> 하이퍼터미널)

◦ Bits per second (baud): 9600

◦ Data bits: 8

◦ Parity: None

◦ Stop bits: 1

◦ Flow Control: Xon/Xoff

1-2. 부팅후 기본 패스워드로 로그인

Version 10.0.32.1 from FLASH image1, factory default config block.

 

Enter password:adminß----------화면에 표시되지 않음 (기본 패스워드)

System Information at 9:23:27 Fri Mar 9, 2007

 

Alteon AD3

sysName:

sysLocation:

 

Switch is up 0 days, 0 hours, 0 minutes and 22 seconds.

Last boot: 9:23:04 Fri Mar 9, 2007 (reset from console)

 

MAC address: aa:aa:aa:aa:aa:aa    IP (If 1) address: 0.0.0.0

Hardware Revision: B

Hardware Part No: AAA_AA-A_AA-A

Software Version 10.0.32.1-SSH (FLASH image1), factory default configuration.

 

------------------------------------------------------------

[Main Menu]

      info    - Information Menu

      stats   - Statistics Menu

      cfg     - Configuration Menu

      oper    - Operations Command Menu

      boot    - Boot Options Menu

      maint   - Maintenance Menu

      diff    - Show pending config changes [global command]

      apply   - Apply pending config changes [global command]

      save    - Save updated config to FLASH [global command]

      revert - Revert pending or applied changes [global command]

      exit    - Exit [global command, always available]

 

>> Main#

 

2. IP 설정

2-1. IP 설정 메뉴

>> Main# /cfg/ip

------------------------------------------------------------

[IP Menu]

      if      - Interface Menu

      gw      - Default Gateway Menu

      route   - Static Route Menu

      frwd    - Forwarding Menu

      rip1    - Routing Information Protocol Menu

      bgp     - Border Gateway Protocol Menu

      port    - IP Port Menu

      dns     - Domain Name System Menu

      bootp   - Bootstrap Protocol Relay Menu

      rearp   - Set re-ARP period in minutes

      metrc   - Set default gateway metric

      cur     - Display current IP configuration

 

>> IP#

2-2. IP 설정 예시

>> IP# if

Enter interface number: (1-256) 1

------------------------------------------------------------

[IP Interface 1 Menu]

      addr    - Set IP address

      mask    - Set subnet mask

      broad   - Set broadcast address

      vlan    - Set VLAN number

      relay   - Enable/disable BOOTP relay

      ena     - Enable IP interface

      dis     - Disable IP interface

      del     - Delete IP interface

      cur     - Display current interface configuration

 

>> IP Interface 1# addr 192.168.2.200/mask 255.255.255.0/br 192.168.2.255

Current IP address:     192.168.2.199

New pending IP address: 192.168.2.200

Current subnet mask:     255.255.255.0

New pending subnet mask: 255.255.255.0

Current broadcast address:     192.168.2.255

New pending broadcast address: 192.168.2.255

 

>> IP Interface 1# ena

Current status: enabled

New status:     enabled

 

>> IP Interface 1#

2-3. Gateway 설정 예시

>> IP# gw

Enter default gateway number: (1-4) 1

------------------------------------------------------------

[Default gateway 1 Menu]

      addr    - Set IP address

      intr    - Set interval between ping attempts

      retry   - Set number of failed attempts to declare gateway DOWN

      arp     - Enable/disable ARP only health checks

      ena     - Enable default gateway

      dis     - Disable default gateway

      del     - Delete default gateway

      cur     - Display current default gateway configuration

 

>> Default gateway 1# addr 192.168.2.1

Current IP address:     192.168.2.1

New pending IP address: 192.168.2.1

 

>> Default gateway 1# ena

Current status: enabled

New status:     enabled

 

>> Default gateway 1#

2-4. IP 설정 확인 (apply 명령어로 적용시킨후 확인 가능)

>> IP# cur

Current IP configuration:

 rearp 10, gw metric strict

 

Current interfaces:

 1: 192.168.2.200   255.255.255.0   192.168.2.255,   vlan 1, enabled

 

Current default gateways:

 1: 192.168.2.1,     intr 2, retry 8, arp disabled, enabled

 

Current static routes:

 

Current IP forwarding settings: ON, dirbr disabled

 

Current local networks:

 

Current IP port settings:

 1: ON

 2: ON

 3: ON

 4: ON

 5: ON

 6: ON

 7: ON

 8: ON

 9: ON

 

Current RIP settings:

 OFF, update 30

 split horizon

 

Current BGP configuration: OFF

 

Current BGP peer configuration:

 

Current BGP filter configuration:

 

Current DNS settings:

 0.0.0.0, 0.0.0.0, none

 

Current BOOTP relay settings: OFF

 0.0.0.0, 0.0.0.0

Note: there are pending config changes; use "diff" to see them.

 

3. 포트 링크 설정

3-1. 포트 모드 설정 및 스피드 설정

# /cfg/po 1[포트번호]

# fast

# speed 100

# mode full

# auto off

 

3-2. auto negotiation 설정

# /cfg/po 1[포트번호]

# fast

# speed any

# mode any

# auto on

 

4. SLB(Server Load Balancing)

4-1. SLB 설정 메뉴

>> Main# cfg/slb

------------------------------------------------------------

[Layer 4 Menu]

      real    - Real Server Menu

      group   - Real Server Group Menu

      virt    - Virtual Server Menu

      filt    - Filtering Menu

      port    - Layer 4 Port Menu

      gslb    - Global SLB Menu

      layer7 - Layer 7 Resource Definition Menu

      sync    - Config Synch Menu

      adv     - Layer 4 Advanced Menu

      on      - Globally turn Layer 4 processing ON

      off     - Globally turn Layer 4 processing OFF

      cur     - Display current Layer 4 configuration

4-2. 리얼 서버 설정

>> Layer 4# real 1

------------------------------------------------------------

[Real server 1 Menu]

      layer7 - Layer 7 Command Menu

      rip     - Set IP addr of real server

      name    - Set server name

      weight - Set server weight

      maxcon - Set maximum number of connections

      tmout   - Set minutes inactive connection remains open

      backup - Set backup real server

      inter   - Set interval between health checks

      retry   - Set number of failed attempts to declare server DOWN

      restr   - Set number of successful attempts to declare server UP

      addport - Add real port to server

      remport - Remove real port from server

      remote - Enable/disable remote site operation

      proxy   - Enable/disable client proxy operation

      submac - Enable/disable source MAC address substitution

      ena     - Enable real server

      dis     - Disable real server

      del     - Delete real server

      cur     - Display current real server configuration

# /cfg/slb/real 1    <-   리얼서버 번호 1 지정

# rip 192.168.2.101

# enable

# /cfg/slb/real 1    <-   리얼서버 번호 2 지정

# rip 192.168.2.102

# enable

 

# /cfg/slb/real 1    <-   리얼서버 번호 3 지정

# rip 192.168.2.103

# enable

 

 

 

 

 

4-3. 리얼 서버 그룹 설정

>> Main# cfg/slb/group 1

------------------------------------------------------------

[Real server group 1 Menu]

      metric - Set metric used to select next server in group

      content - Set health check content

      health - Set health check type

      backup - Set backup real server or group

      name    - Set real server group name

      realthr - Set real server failure threshold

      viphlth - Enable/disable VIP health checking in DSR mode

      add     - Add real server

      rem     - Remove real server

      del     - Delete real server group

      cur     - Display current group configuration

 

# add 1/add 2/add 3 <- 리얼 IP 를 그룹 1번에 지정

# health http     <- Health Check 타입을 설정

health link|arp|icmp|tcp|http|dns|pop3|smtp|nntp|ftp|imap|radius|sslh|script-x<n>|udpdns|ldap

# metric hash    <- metric hash 방식으로 지정(동일한 유저로 부터의 서비스요청 – 동일한 서버연결)

metric leastconns|roundrobin|minmisses|hash|response|bandwidth

 

4-4. 가상 서버 설정

>> Main# cfg/slb/virt 1

------------------------------------------------------------

[Virtual Server 1 Menu]

      service - Virtual Service Menu

      vip     - Set IP addr of virtual server

      dname   - Set domain name of virtual server

      layr3   - Enable/disable layer 3 only balancing

      ena     - Enable virtual server

      dis     - Disable virtual server

      del     - Delete virtual server

      cur     - Display current virtual configuration

 

# vip 192.168.2.100 <- virtual IP 지정

# enable

# service http <- 서비스 포트 번호, Well-Known 포트의 경우는 서비스 이름으로 지정

4-5. 클라이언트 / 서버 포트 지정

>> Main# cfg/slb/port 1

------------------------------------------------------------

[SLB port 1 Menu]

      client - Enable/disable client processing

      server - Enable/disable server processing

      rts     - Enable/disable RTS processing

출처 : http://www.nicehosting.co.kr/customer/customer_09_view.asp?seqno=25&ctype=1&ktype=3