세이박스

'AD3'에 해당되는 글 1건

  1. Alteon AD3 설정 메뉴얼

Alteon AD3 설정 메뉴얼

서버,보안
 
► Alteon AceDirector 3 (AD3) 장비 설정
1. 콘솔 터미널 연결 설정
1-1. 콘솔 연결 및 하이퍼터미널 실행(시작 -> 프로그램 -> 보조프로그램 -> 통신 -> 하이퍼터미널)
Bits per second (baud): 9600
Data bits: 8
Parity: None
Stop bits: 1
Flow Control: Xon/Xoff
1-2. 부팅후 기본 패스워드로 로그인
Version 10.0.32.1 from FLASH image1, factory default config block.
 
Enter password:adminß----------화면에 표시되지 않음 (기본 패스워드)
System Information at 9:23:27 Fri Mar 9, 2007
 
Alteon AD3
sysName:
sysLocation:
 
Switch is up 0 days, 0 hours, 0 minutes and 22 seconds.
Last boot: 9:23:04 Fri Mar 9, 2007 (reset from console)
 
MAC address: aa:aa:aa:aa:aa:aa    IP (If 1) address: 0.0.0.0
Hardware Revision: B
Hardware Part No: AAA_AA-A_AA-A
Software Version 10.0.32.1-SSH (FLASH image1), factory default configuration.
 
------------------------------------------------------------
[Main Menu]
      info    - Information Menu
      stats   - Statistics Menu
      cfg     - Configuration Menu
      oper    - Operations Command Menu
      boot    - Boot Options Menu
      maint   - Maintenance Menu
      diff    - Show pending config changes [global command]
      apply   - Apply pending config changes [global command]
      save    - Save updated config to FLASH [global command]
      revert - Revert pending or applied changes [global command]
      exit    - Exit [global command, always available]
 
>> Main#
 
2. IP 설정
2-1. IP 설정 메뉴
>> Main# /cfg/ip
------------------------------------------------------------
[IP Menu]
      if      - Interface Menu
      gw      - Default Gateway Menu
      route   - Static Route Menu
      frwd    - Forwarding Menu
      rip1    - Routing Information Protocol Menu
      bgp     - Border Gateway Protocol Menu
      port    - IP Port Menu
      dns     - Domain Name System Menu
      bootp   - Bootstrap Protocol Relay Menu
      rearp   - Set re-ARP period in minutes
      metrc   - Set default gateway metric
      cur     - Display current IP configuration
 
>> IP#
2-2. IP 설정 예시
>> IP# if
Enter interface number: (1-256) 1
------------------------------------------------------------
[IP Interface 1 Menu]
      addr    - Set IP address
      mask    - Set subnet mask
      broad   - Set broadcast address
      vlan    - Set VLAN number
      relay   - Enable/disable BOOTP relay
      ena     - Enable IP interface
      dis     - Disable IP interface
      del     - Delete IP interface
      cur     - Display current interface configuration
 
>> IP Interface 1# addr 192.168.2.200/mask 255.255.255.0/br 192.168.2.255
Current IP address:     192.168.2.199
New pending IP address: 192.168.2.200
Current subnet mask:     255.255.255.0
New pending subnet mask: 255.255.255.0
Current broadcast address:     192.168.2.255
New pending broadcast address: 192.168.2.255
 
>> IP Interface 1# ena
Current status: enabled
New status:     enabled
 
>> IP Interface 1#
2-3. Gateway 설정 예시
>> IP# gw
Enter default gateway number: (1-4) 1
------------------------------------------------------------
[Default gateway 1 Menu]
      addr    - Set IP address
      intr    - Set interval between ping attempts
      retry   - Set number of failed attempts to declare gateway DOWN
      arp     - Enable/disable ARP only health checks
      ena     - Enable default gateway
      dis     - Disable default gateway
      del     - Delete default gateway
      cur     - Display current default gateway configuration
 
>> Default gateway 1# addr 192.168.2.1
Current IP address:     192.168.2.1
New pending IP address: 192.168.2.1
 
>> Default gateway 1# ena
Current status: enabled
New status:     enabled
 
>> Default gateway 1#
2-4. IP 설정 확인 (apply 명령어로 적용시킨후 확인 가능)
>> IP# cur
Current IP configuration:
 rearp 10, gw metric strict
 
Current interfaces:
 1: 192.168.2.200   255.255.255.0   192.168.2.255,   vlan 1, enabled
 
Current default gateways:
 1: 192.168.2.1,     intr 2, retry 8, arp disabled, enabled
 
Current static routes:
 
Current IP forwarding settings: ON, dirbr disabled
 
Current local networks:
 
Current IP port settings:
 1: ON
 2: ON
 3: ON
 4: ON
 5: ON
 6: ON
 7: ON
 8: ON
 9: ON
 
Current RIP settings:
 OFF, update 30
 split horizon
 
Current BGP configuration: OFF
 
Current BGP peer configuration:
 
Current BGP filter configuration:
 
Current DNS settings:
 0.0.0.0, 0.0.0.0, none
 
Current BOOTP relay settings: OFF
 0.0.0.0, 0.0.0.0
Note: there are pending config changes; use "diff" to see them.
 
3. 포트 링크 설정
3-1. 포트 모드 설정 및 스피드 설정
# /cfg/po 1[포트번호]
# fast
# speed 100
# mode full
# auto off
 
3-2. auto negotiation 설정
# /cfg/po 1[포트번호]
# fast
# speed any
# mode any
# auto on
 
4. SLB(Server Load Balancing)
4-1. SLB 설정 메뉴
>> Main# cfg/slb
------------------------------------------------------------
[Layer 4 Menu]
      real    - Real Server Menu
      group   - Real Server Group Menu
      virt    - Virtual Server Menu
      filt    - Filtering Menu
      port    - Layer 4 Port Menu
      gslb    - Global SLB Menu
      layer7 - Layer 7 Resource Definition Menu
      sync    - Config Synch Menu
      adv     - Layer 4 Advanced Menu
      on      - Globally turn Layer 4 processing ON
      off     - Globally turn Layer 4 processing OFF
      cur     - Display current Layer 4 configuration
4-2. 리얼 서버 설정
>> Layer 4# real 1
------------------------------------------------------------
[Real server 1 Menu]
      layer7 - Layer 7 Command Menu
      rip     - Set IP addr of real server
      name    - Set server name
      weight - Set server weight
      maxcon - Set maximum number of connections
      tmout   - Set minutes inactive connection remains open
      backup - Set backup real server
      inter   - Set interval between health checks
      retry   - Set number of failed attempts to declare server DOWN
      restr   - Set number of successful attempts to declare server UP
      addport - Add real port to server
      remport - Remove real port from server
      remote - Enable/disable remote site operation
      proxy   - Enable/disable client proxy operation
      submac - Enable/disable source MAC address substitution
      ena     - Enable real server
      dis     - Disable real server
      del     - Delete real server
      cur     - Display current real server configuration
# /cfg/slb/real 1    <-   리얼서버 번호 1 지정
# rip 192.168.2.101
# enable
# /cfg/slb/real 1    <-   리얼서버 번호 2 지정
# rip 192.168.2.102
# enable
 
# /cfg/slb/real 1    <-   리얼서버 번호 3 지정
# rip 192.168.2.103
# enable
 
 
 
 
 
4-3. 리얼 서버 그룹 설정
>> Main# cfg/slb/group 1
------------------------------------------------------------
[Real server group 1 Menu]
      metric - Set metric used to select next server in group
      content - Set health check content
      health - Set health check type
      backup - Set backup real server or group
      name    - Set real server group name
      realthr - Set real server failure threshold
      viphlth - Enable/disable VIP health checking in DSR mode
      add     - Add real server
      rem     - Remove real server
      del     - Delete real server group
      cur     - Display current group configuration
 
# add 1/add 2/add 3 <- 리얼 IP 를 그룹 1번에 지정
# health http     <- Health Check 타입을 설정
health link|arp|icmp|tcp|http|dns|pop3|smtp|nntp|ftp|imap|radius|sslh|script-x<n>|udpdns|ldap
# metric hash    <- metric hash 방식으로 지정(동일한 유저로 부터의 서비스요청 – 동일한 서버연결)
metric leastconns|roundrobin|minmisses|hash|response|bandwidth
 
4-4. 가상 서버 설정
>> Main# cfg/slb/virt 1
------------------------------------------------------------
[Virtual Server 1 Menu]
      service - Virtual Service Menu
      vip     - Set IP addr of virtual server
      dname   - Set domain name of virtual server
      layr3   - Enable/disable layer 3 only balancing
      ena     - Enable virtual server
      dis     - Disable virtual server
      del     - Delete virtual server
      cur     - Display current virtual configuration
 
# vip 192.168.2.100 <- virtual IP 지정
# enable
# service http <- 서비스 포트 번호, Well-Known 포트의 경우는 서비스 이름으로 지정
4-5. 클라이언트 / 서버 포트 지정
>> Main# cfg/slb/port 1
------------------------------------------------------------
[SLB port 1 Menu]
      client - Enable/disable client processing
      server - Enable/disable server processing
      rts     - Enable/disable RTS processing

출처 : http://www.nicehosting.co.kr/customer/customer_09_view.asp?seqno=25&ctype=1&ktype=3